How To Adjust The Suspension Of A Motorcycle Fork? Measure The Sinking Amount First, Then Adjust The Compression And Rebound Damping

BLOG 150

Adjust the motorcycle fork and measure the ride sinkage first (rider sag). Spring preload determines where the front fork starts working after the rider gets on the vehicle, compresses the speed at which the front fork of the damping tube retracts, and rebounds the speed at which the damping tube extends back. When encountering continuous bumps, if the fork is lower than the fork, pay attention to whether it extends back in time between the two impacts. This detail can help you determine which regulator to use.

First identify the regulator and write down the original settings

Check the manual by model, year, and actual fork installation to confirm where and how much spring preload (preload), compression damping (compression damping), and rebound damping (rebound damping) can be adjusted. The left and right fork legs can be divided into two parts. Taking the BME-28199-E1 version manual of the Yamaha MT-09 as an example, the spring preload on both sides should be set to the same value, the compression damping should only be adjusted on the left fork leg, and the rebound damping should only be adjusted on the right fork leg. When the manual lists only some external adjustment functions, follow the items supported by the vehicle. Yamaha MT-09 Owner’s Manual, Pages 5-45 to 5-47

Before you start, write down your current settings. Preload records the number of lines, turns, or specified dimensions according to the manual, while damping records the number of squares or turns exiting from the reference position specified in the manual. If the manual specifies counting from the full-level position, simply turn to the dead center to stop, and then return in the specified direction. When recording, write the complete reading such as “Exit 6 blocks from the entire level”. When you need to re-establish a benchmark, start by setting the standard in the manual. Yamaha MT-09 Owner’s Manual · Honda CRF450R/RX/RWE Owner’s Manual

Measure the sinking volume three times and then decide which side to adjust the preload to

First, select the measurement point. The telescopic fork can be selected on the same side with the dust-proof lower edge and the fixed point that moves with the front axle, and the distance between the two points can be measured along the fork tube axis. When the vehicle manual specifies the point of acquisition or measurement direction, follow the manual, especially when comparing the reading with the factory target value. Use the same pair of dots three times. Ultraviolette F77 Owner’s Manual, Front Suspension Chapter

ReadingHow to measure
L₀ — Fork fully extendedOn level ground, securely support the motorcycle with a suitable stand so the front wheel is off the ground and the fork can extend fully.
L₁ — Motorcycle onlyLower the front wheel to the ground. Have a helper hold the bike upright and take the reading once the fork settles.
L₂ — With riderWear your usual riding gear and sit in your normal riding position with both feet on the pegs. Have someone hold the bike upright while the measurement is taken.

Empty vehicle sinkage = L₀ − L₁. Ride sinkage = L₀ − L₂. Assuming the three readings are 140, 120, and 105 mm, the empty vehicle sink is 20 mm, and the riding sink is 35 mm. The 35 mm value in the example is used to demonstrate the algorithm. The target value needs to be checked for information about the corresponding vehicle model or the installed fork.

Measuring Motorcycle Front Fork Rider Sag With A Tape Measure While The Rider Sits On The Bike To Adjust Suspension Preload

Under the same load, if the riding sink is too large, the preload will be slightly increased according to the manual and the test will be repeated; if it is too small, the preload will be reduced. For linear springs, increasing the preload will cause the fork to stop higher under the same load, and the spring stiffness (N/mm) will still be the original value. The less sinking there is, the less travel the fork can extend downward from the riding position. If the upper or lower limit of the preload adjustment still does not meet the vehicle model target, or if the manual gives two ranges but cannot get the empty vehicle and riding readings to meet the standards at the same time, ask a technician to check whether the spring stiffness matches the actual load. Motorcycle suspension information from the General Technical College of America

When adjusting damping, distinguish which section of the impact occurs

The front wheel hits the protrusion, shortening the fork; after passing the protrusion, the spring pushes the fork back. Fork oil flows through the corresponding oil path in two directions, forming compression and rebound resistance. The impact sensation when entering the kan and the stretching movement after passing the kan occur at different stages. Recognize this during the test ride before deciding which screw to move. Motorcycle fork damping parameter test

What you feelWhat to try first
A single bump sends a sharp jolt through the handlebars.Check that tire pressure is within spec and the fork moves smoothly. Then try reducing compression damping and ride over the same bump again.
The front end dives too quickly under normal braking.Recheck rider sag. If it’s within spec, add a little compression damping and see whether the fork dives more slowly.
The front end springs up quickly after a bump and keeps bobbing.Try adding rebound damping. Check whether the front end settles sooner after the bump.
The first bump feels fine, but the front end rides lower and feels harsher over the next few.Try reducing rebound damping. If the fork can’t extend far enough between hits, it starts each compression deeper in its travel, leaving less room to absorb the next bump.

These phenomena are used to select the direction of the trial adjustment. Especially if the bottom is hit repeatedly, first check the amount of sinking and the status of the fork, and then use the model manual to judge the spring, damping or other factors. Honda CRF450R/RX/RWE Owner’s Manual, Front Suspension Adjustment Guide

Change only one item at a time and retest using the same section of road

Fine-tune the stride length as permitted in the manual. For example, Honda’s 2020 CRF450R/RX/RWE manual requires that the compression and rebound damping of the fork be adjusted one bar at a time and then test-ride after adjustment. Choose a safe, repeatable section of road surface and try to keep the load, speed, and braking force consistent. If the changes are worse, return to the previous setting; if you cannot tell which change caused it, go back to the recorded baseline and try again. Honda CRF450R/RX/RWE Owner’s Manual

If the fork legs leak oil, the fork pipe is damaged, or the front fork is obviously stuck when pressed down and extended during parking inspection, stop the test ride first and adjust it after maintenance. Once you’ve confirmed the fork is moving smoothly, note the load, ride sinkage, preload position, and two damping settings for this time. The next time the load is changed, the sinking amount is retested before deciding whether dynamic damping is needed. Yamaha Fork Inspection Guidelines

The prev:

Related recommendations

Expand more!